Ellis intake


Truck finds of all conditions OLD ADDS WILL BE REMOVED

User avatar

Golden Jubilee
Golden Jubilee

Posts: 1887

Joined: Thu Nov 29, 2012 10:40 am

Location: Wichita, Kansas

Post Sat Jun 16, 2018 6:28 pm

Ellis intake

This is an interesting piece I found on Craigslist-

https://tulsa.craigslist.org/pts/d/inte ... 88904.html

Web search seems to indicate that it fit an IH K11 truck with an FAB/RD/Red series engine. Does that look right?

Advertising literature says "Saves a day from Chicago to LA".

Dean
Lifelong Kansan
Grew up with red paint
Moved off the farm 33 years ago.
User avatar

Golden Jubilee
Golden Jubilee

Posts: 4922

Joined: Thu Nov 29, 2012 11:47 am

Location: Bothell, Washington

Post Sat Jun 16, 2018 7:45 pm

Re: Ellis intake

I see these listed every now and then, they are for the RD 450 (I believe) I was wondering if you could section it to make it fit a SD motor?
Gentle Men! you can't fight in here! This is the war room!
User avatar

Golden Jubilee
Golden Jubilee

Posts: 1887

Joined: Thu Nov 29, 2012 10:40 am

Location: Wichita, Kansas

Post Sat Jun 16, 2018 10:16 pm

Re: Ellis intake

BRJ, are all the ones you've seen marked K11? This one looks to have clear markings.

Dean
Lifelong Kansan
Grew up with red paint
Moved off the farm 33 years ago.

Golden Jubilee
Golden Jubilee

Posts: 5170

Joined: Thu Nov 29, 2012 9:28 pm

Location: Lyman, IA

Post Sun Jun 17, 2018 7:48 am

Re: Ellis intake

dean466 wrote:Advertising literature says "Saves a day from Chicago to LA".

Dean

The original "pass everything but a gas pump" modification
User avatar

Golden Jubilee
Golden Jubilee

Posts: 4922

Joined: Thu Nov 29, 2012 11:47 am

Location: Bothell, Washington

Post Sun Jun 17, 2018 10:53 am

Re: Ellis intake

There are 4 of them on ePay right now,

They all have different markings, some just have code like this one, others list specific engines,
But all are for larger engines,

One has 250 on it so May fit BLD 250?

I don't know a ton about these other than I've never seen one for the smaller SD, BD motors
Gentle Men! you can't fight in here! This is the war room!

Golden Jubilee
Golden Jubilee

Posts: 5170

Joined: Thu Nov 29, 2012 9:28 pm

Location: Lyman, IA

Post Sun Jun 17, 2018 1:05 pm

Re: Ellis intake

One listed for K-6 and 7 another stamped BLD269 IHC, so I think there are two for the medium six.
I read years ago about a guy hauling steel plate from Buffalo to Chicago with a K 7 and 40,000 lbs on the flatbed. Said he was way overweight for the time, and did the move after dark, must have been a long trip!
At right around 10 MPG I have no plans for something like that on my 269's I think you'd be lucky to see 5's.
I knew an old car hauler that hauled Ford's out of Chicago. To haul for Ford, you had to drive a Ford. He said they all were cracking blocks back then overworking the car engines in the trucks. One guy put an IHC under the hood of the Ford, and never had a problem, don't know if it was a BLD or RED. He just had to be sure not to open the hood until he was off the property.
User avatar

Golden Jubilee
Golden Jubilee

Posts: 4922

Joined: Thu Nov 29, 2012 11:47 am

Location: Bothell, Washington

Post Sun Jun 17, 2018 5:07 pm

Re: Ellis intake

yea, that one that has IHC 269 on one end has IHC 250 on the other, so must fit BLD motor,

I think the only thing these would be good for is bling under the hood,

on the GMC site they have single two, three, four, five, and six carb intakes available, lots of fittings and linkage issues, Bling

maxresdefault1.jpg
Gentle Men! you can't fight in here! This is the war room!

Return to Diamonds in the Rough

Who is online

Users browsing this forum: No registered users and 5 guests

Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.