? front axle F-160 bore diameter for king pin 55' R110


IHC in the early to mid-fifties.

Yard Art
Yard Art

Posts: 52

Joined: Tue Jan 15, 2013 4:12 pm

Location: boise idaho

Post Sat Apr 05, 2014 8:38 pm

? front axle F-160 bore diameter for king pin 55' R110

Greetings,

I'm replacing the king knuckle pins on a 55' R110 that according to the CTS-11 manual has a F-160 axle. No where can I find out what the bore dimensions/specifications should be for the axle bore where the king pin fits through. The king pin diameter is described as 0.861 inches.

How do I tell if the bore on the axle is worn beyond specs and needs an oversized king knuckle pin?

Thanks,

Neal

Golden Jubilee
Golden Jubilee

Posts: 1806

Joined: Tue Jun 25, 2013 5:26 pm

Location: Dinuba, central CA

Post Sat Apr 05, 2014 9:54 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

I would say the need for an oversze kingpin is slim. I personally have never installed an oversize kingpin.
Take your current kingpins, hit them and clean them up with the wirewheel.
Take a piece of emory cloth on a socket extension and clean up the bores.
Mike the kingpins at several locations each and then install them in there respective axle bores.
Do they go in snug?
Should be NO wobbling.
Now look where the pins exit the bores top and bottom.
It should be easy to see out of round bores now.
I suspect everything is fine.
I assume the kingpins are loose in the spindles otherwise we wouldn't be on this subject.
Get a kingpin kit at NAPA or wherever and go.
Good luck.
1933 IHC Bus. Cpe
1933 IHC B-3 f
1935 C-1 IHC pickup
2 x 1936 IHC C-30 Fbs
3 x 1938 IHC D-2 Pickups
1938 IHC D-30 fb
1941 IHC K-1
2 x 1947 IHC KB-1 Pickups
2x 1953 IHC R pickups

Yard Art
Yard Art

Posts: 52

Joined: Tue Jan 15, 2013 4:12 pm

Location: boise idaho

Post Sun Apr 06, 2014 1:06 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

Thanks and yes one side had notable movement...the other side I could not detect any movement.

...still seems odd there would be a specification somewhere for the bore...

Regards,

Neal

Golden Jubilee
Golden Jubilee

Posts: 5209

Joined: Thu Nov 29, 2012 9:28 pm

Location: Lyman, IA

Post Sun Apr 06, 2014 4:59 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

You are replaceing the bushings aren't you? Are you talking about movement in the part of the knuckle were the pin is stationary? The only time I've seen a problem is when the bushing were worn thru and the pin wollowed out the bore and new bushing would not fix it.

Pile of Parts
Pile of Parts

Posts: 35

Joined: Sun Dec 09, 2012 9:27 pm

Post Sun Apr 06, 2014 5:52 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

If you go to Ebay , I'm sure you'll find a king pin set on there. It is 2 king pins and 4 bushings. There is a tapered bolt on the axle going from the front to the back and has a nut on the back side. When you get that out the King Pin will fall out. You take the new King Pins and Bushings and the part that the brake backing plate is attached to and take it to a machinist. They will press the new bushings into the backing plate mount and then hone them out to about .001 larger than the king Pins. You take it all home and put it back together and grease it and your in fat city. :h0212:

Don

Golden Jubilee
Golden Jubilee

Posts: 1806

Joined: Tue Jun 25, 2013 5:26 pm

Location: Dinuba, central CA

Post Sun Apr 06, 2014 6:46 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

I think that's strange, one kingpin is loose in its axle bore, but OK.
Your options are another front axle assy or an oversized kingpin set.
I honestly don't know which is easier to obtain there.
Here I have an extra R front axle.
Let us know what you decide to do.
1933 IHC Bus. Cpe
1933 IHC B-3 f
1935 C-1 IHC pickup
2 x 1936 IHC C-30 Fbs
3 x 1938 IHC D-2 Pickups
1938 IHC D-30 fb
1941 IHC K-1
2 x 1947 IHC KB-1 Pickups
2x 1953 IHC R pickups

Yard Art
Yard Art

Posts: 52

Joined: Tue Jan 15, 2013 4:12 pm

Location: boise idaho

Post Sun Apr 06, 2014 7:10 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

cornbinder,

Before disassembling the drivers side...I grabbed the spindle and moved it up and down and could see 'slop' or movement between the king pin and the brass bushings. When did this on the passenger side I could not detect any movement between the king pin and the brass bushings. So I removed the drivers side only and I've already secured a king pin set and it is ready to be reassembled. But, before I do this I kinda wanted to measure the bore of the axle to see if it had any excessive wear that I could measure. So far, I haven't been able to find any factory specs on what the bore diameter was originally so I don't have a reference to gauge if it is worn or not. I'm sure I can put it all back together with the new king pin parts I've secured and be fine as others have posted.

thanks for responding,

Neal

Golden Jubilee
Golden Jubilee

Posts: 5209

Joined: Thu Nov 29, 2012 9:28 pm

Location: Lyman, IA

Post Sun Apr 06, 2014 7:56 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

Are you talking about up and down slop? that is controlled with shims behind the trust bearing. The bushings should be a press fit in the knuckle. If the hole the bushing goes in is round, it is ok. If it is worn egg shaped then it needs to be re-bored. The bushings should be reamed after being pressed in.
User avatar

Golden Jubilee
Golden Jubilee

Posts: 2048

Joined: Thu Jan 24, 2013 8:49 pm

Post Tue Apr 08, 2014 7:45 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

I had no problem finding the pin diameter in the CTS-11,it's right there on pg. 2
.861

http://www.hansenwebdesign.com/truck/fi ... 20Axle.pdf

Here's the info from my King pin kit file;

R-100,110,120,130
62905R93 Kit,king pin (standard) Pin size 5.439 L x .861 Dia.
891098R91 Supersedes 62905R93 (FA-10)
530-1043 Raybestos Chassis
8390B Federal Mogul / Moog
R200005 Meritor
KB-473B Elgin
NCP 2621367 NAPA

All above kits are Standard, I did a lot of research and could never find any oversize kits.

The I beam & knuckles can be sleeved when excessively worn and return them to OEM specs,but it is not a DIY job.

You could try here;
http://axledoctors.com:82/index.a5w

or look for another...

Google search results;
https://www.google.com/#q=axle+doctor&start=0
12 yrs.exp. in IH dealer parts dept.
Never argue with a fool...
If you don't have anything nice to say...say nothing.
If you don't learn something new everyday...you weren't paying attention.
THINK! Be sure brain is connected before mouth is in gear.

Golden Jubilee
Golden Jubilee

Posts: 1806

Joined: Tue Jun 25, 2013 5:26 pm

Location: Dinuba, central CA

Post Tue Apr 08, 2014 9:00 pm

Re: ? front axle F-160 bore diameter for king pin 55' R110

I'd call Sid at Nostalgia Sid's and ask him what he would do. Axles are his business.
1933 IHC Bus. Cpe
1933 IHC B-3 f
1935 C-1 IHC pickup
2 x 1936 IHC C-30 Fbs
3 x 1938 IHC D-2 Pickups
1938 IHC D-30 fb
1941 IHC K-1
2 x 1947 IHC KB-1 Pickups
2x 1953 IHC R pickups
Next

Return to L, R and S

Who is online

Users browsing this forum: No registered users and 17 guests

Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.