Page 2 of 3

Re: Parts Link

PostPosted: Fri Dec 30, 2016 11:27 pm
by tinker925
Hi guys,
I've been restoring your IHC instrument clusters for several years now, and I recently added this electronic tachometer to my list of services. It has the original-style faceplate and chrome outer-bezel as the factory KB's and it is the same outside diameter so it will fit into the original dash hole. The original tachs were a cable-driven mechanical style. This is an electronic unit made for a 12-volt system only. It can be programed for a 4, 6, 8 or 10 cylinder engine using a 12-volt system. It is a 4000 rpm operating unit, so check your engine rpms. Please feel free to call 218-849-2759 or email me (Larry) at lar@arvig.net for more information.

Re: Parts Link

PostPosted: Wed Feb 01, 2017 7:41 am
by captainbob
This information sticker was found on a nos interior door handle.
$_57.jpg

Re: Parts Link

PostPosted: Mon Sep 18, 2017 11:54 am
by DOXIN
JimHadfield wrote:Post links to parts vendors using the following format.



*Part Description: Water Pump Rebuild Kit
*Part Number: W6562 (bearing) 41-910-A (Seal) 5043 (gasket)
*Source: Kellogg Automotive
*Source Address: 5562 No. Warren RD, Mariopa Arizona 85139
*Source Web Link: http://www.kelloggautomotive.com
*Phone Number:520-494-7460 Fax 520-494-2011 Toll free 877-499-2011
*Comments:

Water pump rebuild parts for GRD 213 with "cage" type impeller.

Kellogg Auto will also rebuild your pump for you. They were very good to deal with and quite knowledgeable. The cost for the rebuild parts were reasonable IMO. They do have parts for other IHC W/pumps. I spoke to Will. You should have the year, model and engine size before calling.

I have detailed how I rebuilt my water pump and will post that soon.

Re: Parts Link

PostPosted: Fri Feb 02, 2018 1:57 pm
by worthy
*Part Description: Gemmer Steering Boxes. Canadian built Trucks only.
Gasket kit 78-3581
Worm Gear bearings 68-3571
sector shaft bushings 78-3576
sector shaft oil seal 48-3591
*Source:Dennis Carpenter Ford

*Comments: Ford built Gemmer steering boxes under license. I found these parts under Ford trucks 1932 - 47 steering box parts. The bushings needed a bit of reaming and the sector shaft gasket bolt holes were a little out but all in all parts were a good fit and made a huge difference.

GRD-214 expansion plugs

PostPosted: Wed Sep 19, 2018 8:51 am
by Seymour
Concave Expansion Plugs

Dorman 550-028

NAPA or almost anywhere

Re: Door hinge

PostPosted: Mon Mar 18, 2019 5:53 pm
by Dna9804
Hi, guys I’m new to this forum. I have a 47 intl. kB 1 1/2 ton truck, I’m just starting to reassemble after I had some work done to chassis. I have misplaced door hinge to truck. Upper rt. Passenger door.
Does anybody have part to sell?

Re: Parts Link

PostPosted: Mon Apr 01, 2019 6:31 pm
by worthy
DNA, Best to post this in the swap meet section, more guys might see it. Go to board index and scroll down to near the bottom.

KB1 clutch bearing

PostPosted: Tue Sep 24, 2019 4:39 pm
by Bobby K1
I replaced the clutch release bearing on a 1949 KB1 ,green diamond engine with a FEDERAL MOGUL 2005 C. ( does not have to be Federal Mogul ) It is the bearing used IH in later years and can be found at multiple parts stores. It is about 1/4” longer but works fine.

Re: Parts Link

PostPosted: Sun Mar 08, 2020 4:10 pm
by DOXIN
Part Description: Sunvisor bracket and hinge (?)

1947 KB2
$5 plus shipping from 01970


Image

Re: Parts Link

PostPosted: Mon Oct 31, 2022 4:09 pm
by cornbinder89
K6,K7 possibly K-5 axle grease seal that goes on the outer bearing lock nut:
Fleetrite ZAR25935
National 5957S
IHC 52753-HA
None of these are in production so N.O.S. only
As of todays date (Oct 31, 2022) 4 are available here: Not mine no connection to the seller
https://www.ebay.com/itm/284908647689
Hub to spindle seal, according to SKF seal finder:
CR 34994 and this is a unitized oil seal for use with oil or grease bearing.