Page 3 of 7

Re: Rebuilt Wheel Cylinders

PostPosted: Tue Sep 03, 2013 10:18 pm
by IHVineyard
The company's name that rebuilt my wheel cylinders is as follows:

Karps Power Brakes
66 North Central Avenue
Upland, Ca 91786
909-985-0800

Jeff Watts is the owner.

Jeff does high quality work. His services included rebuilding wheel cylinders, master cylinders, power brake boosters, makes brake lines ect. He relined my cylinders with Stainless Steel liners and workmanship is "Outstanding". This guy has a small machine shop just set up to resleave parts. I know other brake shops from all around the country send stuff to Jeff to rebuild. I was quoted cost of $200 or more from other brake shops who intern just send the parts over to Jeff to rebuild. I paid Jeff $180 for each rear wheel cylinder and 130 each for the front wheel cylinder. Not exactly cheep, but the parts are better than new from a spec perspective.

I recommend letting Jeff disassemble the parts since he has the equipment to do so without damaging the original parts. I also plan to have my Hydrovac rebuilt by Jeff. He has access to all the parts and if the parts do not exist he can make them.

Re: Re: Parts Link Format

PostPosted: Tue Sep 17, 2013 12:29 pm
by hermit23
Re: Water Pump Rebuild
*Part Description: Water Pump Rebuild
*Part Number: GD-214 engine and others? Call
*Source: A&T Parts Rebuilders
*Source Address: 776 Westmoreland Drive, Tupelo, MS 38801
*Phone Number: 1(662)-844-4512 - 1-800-748-9567
*Source Web Link: http://www.atrebuilders.com/
*Comments: Rebuild starters, alternators and water pumps. Call for specific applications/availability. I'll be using this option if I can remove a broken bolt from the block.

GRD Oil Filters

PostPosted: Fri Oct 04, 2013 3:49 pm
by Scottso
OEM filter info from MT-52D IH K/KB 1-5 parts manual,then each aftermarket PN crossed to each other.

Deluxe filter (Code 1250)
70690H IH (K/KB1-5 w/ GRD-233A)
LF 506 Fleetguard
CU406 Baldwin
C121E Fram
LF502 Hastings
L24A Luberfiner
51002 WIX
1002 NAPA

From WIX cat.
Style: Cartridge Lube Sock Filter
Service: Lube
Type: By-Pass
Media: Depth
Height: 5.25
Outer Diameter: 4.197
Inside Diameter Top: 0.775
Inside Diameter Bottom: 1.476


70671H IH (K/KB1-5 w/ GRD-175,175A,214,214A,233)
LF505 Fleetguard
JC405 Baldwin / Hastings
C120E Fram
51011 WIX
1011 NAPA

From WIX cat.
Style: Cartridge Lube Sock Filter
Service: Lube
Type: By-Pass
Media: Depth
Height: 5.562
Outer Diameter: 4.063
Inside Diameter Top: 0.539
Inside Diameter Bottom: 1.885




Michiana filter (Code 1251) (All eng's)
92629H IH
P54 Baldwin
P54 Hastings
C150 Fram

O.D.: 3 23/32 (94.5)
I.D.: 1/2 (12.7)
Length: 6 23/32 (170.7)

NLA;
LF 542 Fleetguard
51033 WIX
1033 NAPA

For those who maybe unaware "DeLuxe" & "Michiana" is the manufacturer of the filter assembly not a filter type.

Re: Defroster Hose

PostPosted: Wed Oct 09, 2013 5:25 pm
by autoholic
*Part Description: Defroster Hose K/KB 1-5
*Part Number: GAT 23828
*Source: Rockauto.com
*Source Address: 1073 E Artesia Blvd, Carson Ca, 907467
*Source Web Link: http://www.rockauto.om
*Phone Number: Toll Free: 1-866-762-5288
* Comments: Sold by the foot

Tune-up parts GRD engines

PostPosted: Sat Nov 02, 2013 12:18 am
by Scottso
Using the IH MT-52D parts manual Group 6/0603,0604,0604B. PN's were then all crossed and matched.

For Reference only;
Distributor assy.
95275HA IH
1110095 Delco <Obsolete>
^^^ Superseded By:
1112361 Delco <Obsolete>

Cap
136986H IH
824735 Delco
DR-413 SMP
RR-95 Echlin

Rotor
136990H IH
820445 Delco
DR-158 SMP
RR-83 Echlin

Condenser
1900272 Delco
DR-50 SMP (HD)
RR-174 Echlin
RR-1750 Echlin (HD)

Points
136995H IH
1848038 Delco
1855720 Delco
DR-2227P SMP
CS-763A Echlin (HD)
CS-763P Echlin (Pierced)


Coil (6V)
1115327 Delco
1115103 Delco
UC-14X SMP
IC-7 Echlin

Spark Plug
GRD-175,214,214A 14mm*thread
295 Autolite <non resistor>
J-8 Champion <non resistor>
R45 AC <resistor>
306 Autolite <resistor>
RJ-8 Champion <resistor>

GRD-233,233A 14mm*
R43 AC <resistor>
303 Autolite <resistor>
RJ-6 Champion <resistor>

GRD-175,214,214A 18mm*thread
C87 AC <resistor>
386 Autolite <resistor>
C87 AC = 516 Champion <non resistor AG/Marine>
386 Autolite = 541 Champion <non resistor AG/Marine>

GRD-233,233A 18mm*
C87 AC <resistor>
386 Autolite <resistor>

*Note;
14mm for eng. s/n;
GRD-175-1760 up
GRD-214-65429 up
GRD-214A-4378 up
GRD-233-63954 up
GRD-233A-2029 up
18mm for eng. s/n;
Below GRD-175-1760
Below GRD-214-65429
Below GRD-214A-4378
Below GRD-233-63954
Below GRD-233A-2029

Wire set
96620 Autolite
The only pre-made set found for IH 6cyl. engs. (BG241)

Pertronix Ignitor for 1112361 Distributor assy.
Ignitor 6V Negative Ground 1168LSN6
Ignitor 12V Negative Ground 1168LS
Ignitor 6V Positive Ground 1168LSP6
Ignitor 12V Positive Ground 1168LSP12
1112361 Distributor uses same tune-up parts as 1110095 Distributor which would indicate the above will work in both.

Re: Parts Heater Door Handle

PostPosted: Sat Nov 23, 2013 2:52 am
by ingkey
MAC's Antique Auto Parts
Part Number- 91A-18560-Y


http://macsautoparts.com/early-v8-ford- ... HL1129730/

Re: Front clearance lights

PostPosted: Wed Jan 01, 2014 12:13 am
by slospeed

KB5 spindle parts

PostPosted: Mon Jan 06, 2014 1:01 pm
by Binderboy
Wheel cylinder kit: Raybestos # WK120
Wheel bearings Timken #'s: -cone / cup
1779 / 1729X
26881 / 26883
Thrust bearing : Nice 610V/
NSK 51209V
Steering tie rod ends : Moog ES26R (right hand thread)
Moog ES26L ( left thread)
Source: amazon.com and rockauto.com

Re: Parts Link Format

PostPosted: Mon Jan 27, 2014 12:26 pm
by tinker925
Tired of the your dash cluster looking worse than the rest of your truck? Get your gauge cluster looking and working like the day it rolled out of the factory! I will do a complete restoration of your K or KB dash gauges addressing every detail of the entire unit. I have restored many of these International clusters and treat each one as if it were going in my own vehicle. Your instrument faceplates will look like brand-new and your speedometer, odometer and indicator gauges will all operate properly. A complete restoration is $359.00 together with a quick turnaround time. Please feel free to call 218-849-2759 or email me (Larry) at lar@arvig.net for more information.

Floor Board Screws

PostPosted: Sat Mar 01, 2014 7:11 pm
by FrankMc
5/16 x 5/8, Hex Head, Tap and Screw, Type B Thread, Zinc Plated screws will replace OEM floor board screws using the original clip nuts.