1917 model F


The place to put your 1940 and older "Build Off" story.

Pile of Parts
Pile of Parts

Posts: 41

Joined: Sun Jul 19, 2020 10:49 am

Location: Placerville, CA

Post Wed Nov 04, 2020 9:38 am

Re: 1917 model F

Foot and hand brake linkage:

After correcting the upside down crossmember, the brake linkage has been installed for a fit check. It’s a clever system. The foot brake rod runs down the left side of the frame, and via a torque tube, actuates the outer brake bands. Similarly, the hand brake rod runs down the right side of the vehicle actuating the inner brake bands.

I needed to fabricate two of the shorter rods as the originals were rusted and bent beyond limits. I was able to straighten and save the others. I spent quite a few hours cleaning each clevis and chasing all the threads. A little time spent here will pay dividends during final assembly and rigging. I was able to save all the original jam nuts and clevis forks. Once I’m satisfied with the fit and function, I’ll disassemble for paint.
Attachments
F9BD8DAD-BA71-4D74-ADB6-7F12BE5E8152.jpeg
7181B388-171A-4265-841C-17AB65331A42.jpeg
3E190A5A-506A-426B-AD43-6C6738943E66.jpeg
B2578DF9-4EC8-41BD-A4D4-6EE3E405832B.jpeg

Rookie
Rookie

Posts: 18

Joined: Sun Apr 07, 2013 6:11 am

Post Sat Nov 07, 2020 7:13 am

Re: 1917 model F

Hi Tim, Great to,see your progress, we are just starting restoring our 1919 Model G and have the clutch apart and the overhead valve motor pulled down so we are quite a few steps behind you. It was interesting to see what your dad used to cut wood. Our truck was used as a well boring rig and later used to power a circular saw but not sure where the saw was mounted. Regards John M

Pile of Parts
Pile of Parts

Posts: 41

Joined: Sun Jul 19, 2020 10:49 am

Location: Placerville, CA

Post Sat Nov 14, 2020 4:55 pm

Re: 1917 model F

Magneto setup:

The Bosch DU4 doesn’t seem to have enough spark at low rpm. 60 plus years in the barn didn’t help and who knows when it last ran as a stationary engine. After disassembly and cleaning it actually looks pretty good inside and out and makes a good hot spark above 150 rpm or so. However, it’s not good enough for hand cranking with no impulse. I’m looking for a magneto shop to get it rebuilt properly. My previous magneto guy passed away.

In the meantime, I have a fresh rebuilt Eisemann mag with impulse on the shelf, so I’ll pop that on for a first start attempt. Rotation is correct and it has a 35 degree impulse which should help greatly with starting safely. I’m milling a coupling from 6061 aluminum stock and should have a nice clean setup. I’ll post a photo once done.

I much prefer the period look of the American Bosch DU4, but I’ll take what works for now. Looking forward to a first start attempt soon.
Attachments
F4E7C19E-7804-43F0-A4A2-74D13E20E774.jpeg
Barn fresh, May2019
5BB8ECA4-34A9-4E52-A4F7-A2AF30A666D0.jpeg
Configuration from barn
727862BE-7B0F-48C7-A883-2095A6372E48.jpeg
Bosch DU4
3AD9AE26-3E9B-40C9-AE59-D33289B8898C.jpeg
Eisemann

Pile of Parts
Pile of Parts

Posts: 41

Joined: Sun Jul 19, 2020 10:49 am

Location: Placerville, CA

Post Tue Nov 17, 2020 11:33 am

Re: 1917 model F

New magneto and first start:

I machined a coupling for the Eisemann and it fits up beautifully. I timed it to fire right at top-dead-center and the impulse should fire at 35 degrees past TDC.

With a few shots of gasoline in the primer cups it started on the second crank. That’s the first time it’s ran in 70 plus years and I’m quite pleased. Seems to fire on all four equally and all is normal so far. The fuel tank and line to carburetor is not installed yet, so it runs on the primer cups only at this point. I’m just happy to have a good hot magneto and correct timing.

To do list:
~ fuel tank, clean and install
~ fabricate fuel line to carb
~ route ignition wires properly
~ fabricate hold-down strap for Eisemann magneto
~ source exhaust gaskets (Olsen’s?)

And much more...
Attachments
B26134C3-28C3-446D-AFCC-D748C77DEF25.jpeg
Mill work
31407A85-4ED9-4ED5-A225-8FF8C1A917E7.jpeg
Lathe work
32477CBE-37A4-46E9-B7CE-687096C08E5F.jpeg
New coupling to impulse
83714EDA-E87C-4EBA-B9C4-9BE331FEB289.jpeg
Eisemann magneto

Pile of Parts
Pile of Parts

Posts: 41

Joined: Sun Jul 19, 2020 10:49 am

Location: Placerville, CA

Post Sun Dec 06, 2020 5:24 pm

Re: 1917 model F

Pinstripes on gunstock:

The instruction manual refers to the floor support structure as the “gunstock, left and right.” Original pinstripes are still visible on my Model F. I didn’t notice them though all the rust until the lighting was just at the correct angle. I highlighted the pinstripes with a black sharpie pen and carefully took measurements. For those that might be interested, I documented the location while they were still visible.

I wasn’t planning on doing pinstripes, but these will be reapplied to the gunstocks as originally delivered. Yellow/gold striping on gloss black background.
Attachments
0854F30E-7607-48CD-85EF-DD8E736AAB58.jpeg
Gunstock, right: installed for fit-check
26183A00-B50A-47A9-AC93-1E11D20ECA9E.jpeg
Gunstock, right
User avatar

Golden Jubilee
Golden Jubilee

Posts: 739

Joined: Mon Sep 07, 2015 11:14 am

Post Sun Dec 06, 2020 9:58 pm

Re: 1917 model F

Yellow/gold striping on gloss black background.


Thats going to look nice...

Pile of Parts
Pile of Parts

Posts: 41

Joined: Sun Jul 19, 2020 10:49 am

Location: Placerville, CA

Post Mon Dec 07, 2020 7:52 pm

Re: 1917 model F

jmagarey wrote:...we are just starting restoring our 1919 Model G and have the clutch apart and the overhead valve motor pulled down...


Thanks. Hoping to see your project come together as well. I’ll continue posting my progress with emphasis on the headaches and surprises along the way.

Pile of Parts
Pile of Parts

Posts: 41

Joined: Sun Jul 19, 2020 10:49 am

Location: Placerville, CA

Post Mon Dec 07, 2020 8:03 pm

Re: 1917 model F

Harvey wrote:
Yellow/gold striping on gloss black...

Thats going to look nice...


Thanks. The original colors were a bit of a mystery for awhile. Plenty of barn dust and rust. However, my dad remembers the truck being red and black with some yellow highlights. So I’m going with that.
Attachments
EBCCD1C3-A5BF-4BB1-B22F-E8BAE89FED6E.jpeg
Roll-out from Hangar 1 (March 2019)

Pile of Parts
Pile of Parts

Posts: 41

Joined: Sun Jul 19, 2020 10:49 am

Location: Placerville, CA

Post Sat Dec 12, 2020 2:14 pm

Re: 1917 model F

For those that might be interested, I posted a YouTube of my model F running nicely on the Stromberg M2 carburetor and Eisemann magneto. One may search for “1917 International Harvester Model F”, or follow the link below.

I saw earlier posts regarding interest in throttle linkages and such, so I attempted to show some of these details.

https://youtu.be/43fyF5Rnulw
Last edited by TimAkin on Fri Jan 08, 2021 10:12 am, edited 2 times in total.
User avatar

Golden Jubilee
Golden Jubilee

Posts: 739

Joined: Mon Sep 07, 2015 11:14 am

Post Sat Dec 12, 2020 5:06 pm

Re: 1917 model F

Very good and informative video.
The petcock and tin can primer setup is sweet... I gleaned an idea from that :)
Fun stuff...

Thanks for posting.

Be safe
PreviousNext

Return to 1940 and older Build-Off

Who is online

Users browsing this forum: No registered users and 3 guests

cron
Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.