Trying to identify an engine


Forum designed for the D series and older

Rookie
Rookie

Posts: 1

Joined: Fri Jan 10, 2014 11:31 am

Post Tue Jan 14, 2014 8:16 pm

Trying to identify an engine

I have someone who is looking for a quote to restore a 1930 (we think) pickup, I'm trying to determine which engine is in it. Someone told me the Waukesha XA has no water pump, and the XAH does have one. I certainly don't see anything external to the block that looks like a water pump (I don't have the truck handy to see the other side of it)- but I'm thinking this is an XA: Image

Did these just have a convection generated current to run the water through the radiator? Also, this thing has been sitting parked for who knows how long- I've picked up several resources from elsewhere on the site as far as getting engine parts, but I'm thinking there's a good chance the transmission will have to be rebuilt/replaced (potentially a couple decades of sitting around without being coated in oil would seem to me as a potential danger to rust the bearings and maybe even gears to the point of seizing). Any tips on who would have parts/has experience rebuilding these?

Thanks in advance,

Tom
User avatar

Golden Jubilee
Golden Jubilee

Posts: 1028

Joined: Fri Nov 30, 2012 3:20 am

Location: Melbourne Australia

Post Tue Jan 14, 2014 8:30 pm

Re: Trying to identify an engine

Tom

Most people who restore these old trucks do most of the work themselves as it is very hard to find anyone that wont charge an arm & leg to fix them.

This is what the engine should look like.

Yes the engine does not have a water pump it is what they call thermosiphon.

Trevor
Attachments
P1000986.JPG
P1000986.JPG (5.92 KiB) Viewed 2756 times
P1000985.JPG
P1000985.JPG (5.75 KiB) Viewed 2756 times
http://www.vihtr.com
Veteran International Harvester Truck Registry
https://www.facebook.com/groups/316122235181405/
International Harvester Trucks Pre 1940
User avatar

Golden Jubilee
Golden Jubilee

Posts: 1028

Joined: Fri Nov 30, 2012 3:20 am

Location: Melbourne Australia

Post Tue Jan 14, 2014 8:37 pm

Re: Trying to identify an engine

try again
Attachments
15.jpg
14.jpg
13.jpg
http://www.vihtr.com
Veteran International Harvester Truck Registry
https://www.facebook.com/groups/316122235181405/
International Harvester Trucks Pre 1940
User avatar

Yard Art
Yard Art

Posts: 61

Joined: Fri Nov 30, 2012 5:53 am

Post Tue Jan 21, 2014 5:58 am

Re: Trying to identify an engine

If the gear shift moves through the gears, there is a good chance that the transmission is OK, of course if it had high mileage it should be rebuilt, but transmission and engine bearings hold up well for a long time. Engines often get stuck from moisture coming in an open valve and causing rust in one or more cylinder walls. Jim

Yard Art
Yard Art

Posts: 63

Joined: Sun Feb 03, 2013 4:15 pm

Post Tue Jan 21, 2014 3:25 pm

Re: Trying to identify an engine

I have a 1928 international with the 6 cylinder and the motor was stuck for almost 20 year the person told me I bought the truck off . I used P B blaster spray and went through 3 cans and just kept on spraying the values and cylinder and it free it up plus the truck runs great. I hope the info helps.

Pile of Parts
Pile of Parts

Posts: 39

Joined: Sun Nov 10, 2013 11:21 pm

Location: Saskatchewan Canada

Post Sat Jan 25, 2014 8:16 pm

Re: Trying to identify an engine

What you have there looks like a 6 speed special. Does it have the 2 speed rear axle? The engine is definately a Waukesha Model XA. There will be a plate on the right side behind the carburetor. It may well run if you get the distributor and things tuned up. They are nearly indestructible. CAUTION don't turn the engine if the distributor is stuck as you will break the gears that drive it off the generator.

Return to 1940 and Older

Who is online

Users browsing this forum: No registered users and 5 guests

Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.