OUR 40 FORD


Just keep it clean please....

Golden Jubilee
Golden Jubilee

Posts: 6753

Joined: Thu Dec 27, 2012 12:45 pm

Location: Canada's left Coast

Post Tue Nov 13, 2018 1:41 pm

Re: OUR 40 FORD

https://youtu.be/PORkrY_e_HQ Women drivers? That may be unacceptable in 2018.
You Tube set this video as a recommended link. There are more 1940 Ford videos, including some visitor rides over a closed course at the 1939 - 1940 Worlds Fair at New York.
In 1940, only the Deluxe had left and right tail-lights from the factory. The windshield wipers mounted on "towers". The linkage from the wiper motor connected to a lower shaft and the wiper action was transferred to an upper shaft with a small chain. https://youtu.be/PORkrY_e_HQ I replaced these on my '40 even though the originals looked not too bad. the splined drive to the wiper arm is usually what fails.
Attachments
1940 NY Worlds Fair.jpg
vanity add-on tag
coming home.jpg
JUST LIKE THE ORIGINAL
I would rather have tools I do not need than to need tools I do not have

Golden Jubilee
Golden Jubilee

Posts: 534

Joined: Thu Nov 29, 2012 9:55 am

Location: Scottsdale, Arizona

Post Tue Nov 13, 2018 7:45 pm

Re: OUR 40 FORD

Is this car driving yet?
1956 S-102 Short Bed BD240

Golden Jubilee
Golden Jubilee

Posts: 6753

Joined: Thu Dec 27, 2012 12:45 pm

Location: Canada's left Coast

Post Tue Nov 13, 2018 7:56 pm

Re: OUR 40 FORD

It is not. I am at the mercy of my son's schedule. When he gets a day off we hope to get the Ford running. I would like to do a pre start lube including some light oil spray on the cylinder walls.
I need the voltage to stay above 10.5 for the ECU to work. The dry drag in the engine drags the voltage to under 10.
The weather is crap, so the car may not get outside.
I would rather have tools I do not need than to need tools I do not have

Golden Jubilee
Golden Jubilee

Posts: 534

Joined: Thu Nov 29, 2012 9:55 am

Location: Scottsdale, Arizona

Post Tue Nov 13, 2018 8:18 pm

Re: OUR 40 FORD

Understand completely except for the weather. It’s still in the high 70’s here. Can’t wait to get my truck started, just need brake lines and fuel lines ran. Been spraying my cylinders once a month with oil fogger.
1956 S-102 Short Bed BD240

Golden Jubilee
Golden Jubilee

Posts: 6753

Joined: Thu Dec 27, 2012 12:45 pm

Location: Canada's left Coast

Post Wed Nov 14, 2018 1:56 pm

Re: OUR 40 FORD

I just ordered two cans of fogging oil from the local Canadian Tire store. I can pickup my order at the check-out after I get called. This should be in an hour or so. Very handy.
I would rather have tools I do not need than to need tools I do not have

Golden Jubilee
Golden Jubilee

Posts: 6753

Joined: Thu Dec 27, 2012 12:45 pm

Location: Canada's left Coast

Post Mon Nov 19, 2018 9:01 pm

Re: OUR 40 FORD

Tomorrow is the day we "fog" the cylinders in the Flathead V8. I bought two cans at CANADIAN TIRE. https://www.canadiantire.ca/en/pdp/moto ... 0910p.html
We adapted to the remote filter lines and used a GRACO oil dispenser to pre-lube. It worked rather well. We ran out of time to finish.

The GRACO dispenser puts out 40 psi.
Attachments
connection to the filter.jpg
GRACO PI; TRANSFER 30 PSI.jpg
GRACO OIL PRE-LUBE PUP..jpg
I would rather have tools I do not need than to need tools I do not have

Golden Jubilee
Golden Jubilee

Posts: 6753

Joined: Thu Dec 27, 2012 12:45 pm

Location: Canada's left Coast

Post Fri Nov 23, 2018 10:00 pm

Re: OUR 40 FORD

It rained all day and the shop was cold. My truck is in a local shop for new brake lines. I am stuck at home.
I had the heat on but I gave up on the car and went to the house.
Attachments
BBS ON THE WELD POSITIONER.jpg
I would rather have tools I do not need than to need tools I do not have
Previous

Return to Non-IH discussion

Who is online

Users browsing this forum: No registered users and 4 guests

Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.